79 Zeilen
5.3 KiB
C
79 Zeilen
5.3 KiB
C
/************************************************************************************
|
|
Z21 Ethernet DCC Command Station Interface config file
|
|
Copyright (c) 2015-2023 by Philipp Gahtow
|
|
***********************************************************************************/
|
|
|
|
/*-------------**********************************-----------------------------------
|
|
/ ************ CHANGE TO SET UP YOUR INDIVIDUAL CONFIGURATION ***************
|
|
/ => uncomment ("//" or #undef) the following lines, if you not USE the Interface!
|
|
/-------------**********************************-----------------------------------*/
|
|
|
|
//#define S88N //S88N Interface (max 62 * 8 Module)
|
|
|
|
//#define WIFI //WiFi Interface über Serial-Port für Arduino UNO/MEGA/DUE zum ESP 8266
|
|
//#define WLAN Serial2 // (DEFAULT = Serial2!) use not the standard WLAN Serial Interface. Select another serial:
|
|
//#define Z21VIRTUAL // WiFi over SoftSerial for UNO only! - LAN and LocoNet will be inaktiv!
|
|
|
|
#define LAN //LAN Ethernet Z21 LAN Kommunikation mit W5100 oder ENC28 Ethernet Shield. Bitte diese IP nur über die Webseite (http://192.168.0.111) ändern! (not for ESP8266 and ESP32)
|
|
//#define ENC28 //USE a ENC28J60 module - instead of w5100 Shield (MEGA only!)
|
|
//#define LANmacB2 0xEF //Byte2 (DEFAULT = 84:2B:BC:EF:FE:ED!) change optional LAN MAC Address. MAC starts with: „84:2B:BC:..Byte*2..:..Byte*1..:..Byte*0..“
|
|
//#define LANmacB1 0xFE //Byte1
|
|
//#define LANmacB0 0xED //Byte0
|
|
//#define LANTimeoutDHCP 10000 //(DEFAULT!) Timeout to wait for a DHCP respose (Fix default Time: 5 sec)
|
|
|
|
// #define DCCGLOBALDETECTOR //DCC Railcom Global Detector for MEGA on Serial Port 3 (RX only) - (not for ESP8266 and ESP32)
|
|
|
|
#define XPRESSNET //XpressNet Auto Master/Salve Interface (not for ESP8266 and ESP32)
|
|
|
|
//#define LOCONET //LocoNet Interface (Timer1, Timer5 on MEGA, with LocoNet2 Library on ESP32)
|
|
//#define LnSLOTSRV //LocoNet Master-Mode: provide a Slot Server for Loco to use FRED & DaisyII
|
|
//#define LnBufferUSB //LocoNet LocoBuffer-USB at 57600 bps (Achtung: kein Debug über Serial Monitor möglich!)
|
|
|
|
//#define BOOSTER_EXT //External Booster Interface (zB. ROCO, CD[E])
|
|
|
|
#define BOOSTER_INT //internal Booster Interface (zB. TLE5206)
|
|
#define BOOSTER_INT_MAINCURRENT //Standard Short Circuit Detection over current Sense resistor (VAmpIntPin) activate the current sensor for prog track and SHORT CIRCUIT Sense over MAINCURRENT
|
|
#define BOOSTER_INT_CURRENT_SHORT_DETECT
|
|
#define DETECT_SHORT_INT_WAIT 20 //(OPTIONAL) Time in ms after internal short circuit is detected and power will switch off
|
|
#define DETECT_SHORT_INT_VALUE 2000 //(OPTIONAL) value = (Amper * senseResist) / (Uref / 1024)
|
|
|
|
/* (DEFAULT OFF - OPTIONAL!) activate only one - Short2 detection PIN reading use: (only one can be active!)*/
|
|
//#define BOOSTER_INT_TLE5206 //internal Booster with TLE5206 or
|
|
//#define BOOSTER_EXT_CDE //external CDE Booster
|
|
|
|
//#define PROG_OUT_INVERT //(DEFAULT OFF!) invert the Output Signal for Service-Mode (Prog-Relay) - for L298n H-Bridge usage without Relay!
|
|
//#define ADD_ACK_COMP //(DEFAULT OFF!) Comperator to detect exact the ACK pulse over interrupt
|
|
|
|
//#define DALLASTEMPSENSE //Dallas 18B20 Temperatur Sensor for Arduino MEGA only!
|
|
|
|
//#define Z21DISPLAY FIND //SSD1306 OLED I2C Display and Address for config Data for Arduino MEGA and ESP only! -->MEGA: 20(SDA), 21(SCL) || -->ESP8266: D2(SDA), D1(SCL)
|
|
//If you not know the Display I2C Address (normal: 0x3C) leave the value "FIND" so the central will search for it when starting!
|
|
//#define Z21DISPLAY_SH1106 //(DEFAULT OFF!) use OLEDs based on SH110X drivers
|
|
//#define Z21DISPLAY_CONTRAST 150 //(OPTIONAL) higher contrast (0..255; default = 20)
|
|
//#define AMP_DECIMALS 1 //(OPTIONAL) OLED decimal digits of precision for Amper on the Rail (default: x.xxA = 2)
|
|
|
|
#define FS128 //default speed steps (Fahrstufen) => possible values are: FS14, FS28, FS128
|
|
|
|
#define Uref 1.1 // measured reference voltage ARef-pin, individual value for every Arduino
|
|
// #define EXTERNAL_UREF_1V1 //optional: AREF with external 1.1 Volt, to get better CV# read with Arduino UNO
|
|
|
|
// #define INA219 0x40 //INA219 I2C current Sensor and Address for Arduino MEGA and ESP only!
|
|
#define senseResist 0.33 //or 0.1 // actual resistor for measuring current on track
|
|
|
|
/***************************************************************/
|
|
/*------------------DEBUG-ONLY---------------------------------*/
|
|
/***************************************************************/
|
|
#define Debug Serial //(DEFAULT = Serial!) use not the Default Standard Debug Serial Interface. Select another serial:
|
|
#define DebugBaud 115200 //Activate Debug on "Serial" with speed setting (on ESP8266 with LocoNet only 16660 baud)
|
|
|
|
/*---------- select what to show (options): --------------*/
|
|
#define DEBUG //To see System-DATA on Serial
|
|
//#define DEBUG_WLAN_CONFIG //to see config data of Wifi ESP8266 (IP, Pw, ..)
|
|
//#define REPORT //To see Sensor Messages (LocoNet & S88)
|
|
#define REQEST //To see answer Request Messages (Lok , Switch, CV)
|
|
//#define LnDEB //To see RAW DATA of LocoNet Protokoll
|
|
//#define XnDEB //To see XpressNet Data
|
|
//#define Z21DEBUG //to see Z21 LAN control data
|
|
//#define Z21DATADEBUG //to see RAW DATA of Z21 LAN Protokoll
|
|
//#define Z21SYSTEMDATADEBUG //to see the system data mainpower and temp
|